Front splitter

So the Caddy is looking much better after last weeks lowering - but I'd love to go lower. Practicality and an empty wallet stop me from going any further though. But there are some visual tricks to make the van appear a little lower to the ground - one of these is by adding a front splitter.

Part of the appeal of modifying vehicles from the VAG family is that every now and then you'll find a part from another vehicle that suits yours perfectly. One of these parts is the front splitter from Seat's Leon Cupra R - part number 1ML 805 903 if you're interested.

An extra horizontal line at the front draws your eye nearer to the ground

Just brushing the green stuff

The sill line is now followed around to the front of the vehicle

Only a small part but it makes such a difference visually.

One word of note: please don't go on eBay and buy from someone selling a 'brand new, still in the wrapper, RARE!' front splitter - they're not rare! Phone your local TPS or Seat Dealer and order one from them and hopefully you'll get one for a sensible (and not over-inflated) price.

Lowering tweaks

Finally, a free morning to get the rear shocks changed for something a little stiffer, drop the rear a couple of notches on the hangers, and then adjust the front coils to suit.

There's just a small matter of re-centering the rear wheels and we're done. Here's the results:

Much better I'm sure you'll agree.

Big thanks must go to the talented JC at JC Motors for taking his time to get that 'just right' stance.

The RAD Roadtrip

370 miles, several UK towns, cities and motorways later, and we're back from a mini-weekend break that involved bolting-up a few new parts to the Caddy.

First up was a Friday morning blast down to RAD: Reflex Auto Design in Brixworth, just north of Northampton. Job one was to fit a sliding-door rail cover, painted in Raven Blue this more than finishes off the side of the van:

Next up (while the paint is in the gun), a rear spoiler to finish off the rear end:

And finally, a sump-guard is bolted up to replace the original plastic unit and allow us to run the ride-height a little nearer the tarmac without the worry of speedbumps.

All excellent products and RAD have been a pleasure to deal with from initial emails to driving away. Quality is high and they take pride in what they do.

Just before driving away we caught a glimpse (well, had a good nosey around) another Caddy that was in for some last-minute tweaks before Ultimate Dubs. I'd seen this van before in Magazines and on the forums, but to see it in it's new guise, show-fresh and ready to roll left me absolutely awe-struck. More info on this in the next post...

Wheels and tyres are on!

The long Winter-wait is at an end; the Helios are finally on.

Tyres were sourced from Camskill - great value for money on brand-name tyres, good stock availability and cheap, quick delivery makes these my first choice every time for buying tyres.

Money saved here has meant we can jump up a level, quality-wise; spec'ing a set of four Falken FK452 in 235/35/19 to perfectly match the 19x8.5 wheels without any impractical stretch of the previously fitted wheels. These also have little effect on the speedo being within 2% of the same rolling diameter as the stock 15" steels.

But who to fit them? Our local tyre-fitting shop don't seem to like us walking in with our tyres - there's no money to be made for them - so after some inquiries and a word-of-mouth recommendation, we got in touch with Stuart at Unique Tyres.

Stuart turned up in his kitted-out Merc Sprinter, fitted a brand new head to his fitting machine and had the four wheels built-up and balanced in no time. For the total sum of £60, a cup of tea and plenty of v-dub chat, the wheels were then checked and mounted in a matter of minutes.

Visually, the front needs to come back down a bit - maybe the back a touch too. It's also apparent that the rear wheels are pulling forwards in the arch; common for modern lowered Volkswagens with a beam rear-end. Hopefully a quick trip to see JC at JC Motors should rectify these.

I'm absolutely over-the-moon with the way the Helios wheels have transformed the look of the Caddy. They keep that whole 'factory' OEM look - and the rarity-factor of not seeing many sets about appeals in a world of endless BBS replicas and cheap Supermarket alloys.
In particular, I like the way the centre-cap matches the centre of the steering wheel - the way VW would have done it if they were building a Caddy without budget constraints:

So there we have it; just a few more lows and a tweak of the stance and we're almost there! Time to turn my focus back to the interior...

Retail therapy

The hammering of the credit card has begun!

Well, not quite. I've made some tentative enquiries with Reflex Auto Design for a few things (hopefully) before Ultimate Dubs in March. Firstly a sliding door rail cover, painted in Raven Blue. A rear spoiler, bought as part of a forum group buy, painted in Raven Blue at the same time then fitted. And finally a sump guard so I can wind the front suspension back down a little and not clench every time I see a speed bump!

The spending didn't stop there. Today's trip to Dubfeeze has seen us pick up a new tax disk holder, some replenishments of Meguiar's cleaning products (roll-on Spring!) and a set of UK-legal pressed metal plates complete with German dealer surrounds:

There didn't seem to be many Caddys kicking around at Dubfreeze, but then again, it was too cold to go searching for any length of time! Here's a couple:

Fingers-crossed I'm sorted for a tyre-fitter too, so the Helios could be on sooner than expected - there won't be any more snow now, right?

The fins are in...

With one last trimming session using two more lower side inserts to 'blend' the edges to the existing bumper, we're finally ready for a coat of black plastic paint and pop into place. Bonded in with a EvoStick's Time Bond contact adhesive and then finish up any gaps with Black Sikaflex, I'm hoping that nothing falls out on the way to work in the morning!

Here's the end result, much better than the gaping hole that was there before:

Not a bad job for someone that has a dislike of working with plastics, spray paints and glue! I did mention in the previous post that I was looking into something different for the finish - well, I've decided against it at the moment... I was thinking of stickerbombing the two horizontal fins but then thought this might attract too close a glance at my handywork (and the whole stickerbomb thing is a little 'last year'), hence I'm leaving them black... for now.

More Fin Trim Fun

Following on from the previous post, time for a bit more fine-tuning of the replacement fin section for the bumper.

Out with the junior hacksaw for some precise cutting:

Once a full bumper, now reduced to 60cm wide piece!

Then followed quite a lot of cut-a-bit, measure-a-bit, cut-a-bit, trial-fit, measure, cut, try, repeat, repeat... until:

Okay, so the plastic is a little wonky in the middle, but this tidies-up the front-end instantly. On with a quick coat of black plastic bumper paint and I've a little something else in store before final fitment... don't worry, it's not that horrible boy-racer mesh grille or anything too tacky!!!

Fitting gifts

There's not much happening between Christmas and New Year so I thought I'd take advantage of a day's fine weather to give the van a much-need clean. This is also a great opportunity to fit the gifts I received for Christmas!

First up; a set of Heko wind deflectors:

For no other reason than I like them - I have a set fitted to the T5 too - ideal for when you want some fresh air in but not the rain, easy to fit too - no more than a minute or so.

Then, a swap from the standard silver lettering to some genuine German red lettering:

These must give me another 15bhp, right?

Let the fin trim begin

A quick progress update. The carpet-lining has ground to a halt, two reasons; firstly, I ran out of glue for doing the carpeting in one bulk session and didn't want to start a bit without being able to finish. And secondly, I ran out of talent - I made a complete balls-up of the headlining - with the headlining panel removed I had it covered in glue ready to roll out the headlining fabric, got half way across the board and (whilst working in the confines of a cramped single-garage) moving from one end of the board to the other I let the fabric roll back up on itself which smeared the slowly drying glue onto the visible side.

Annoyed with myself I closed the garage door and called it a day (sometimes the best way) only to find out that the glue had gone off and stuck the first section of the fabric permanently to the board. Fold board in half, go to VW and order new board.

So in the mean time I've been setting about the reinstating of the lower fins in the bumper:

The big-hole, some people like it but not me.

Step one was to find a bumper. A quick post in the wanted section on Caddy2k and within 48 hours I'd got one... for nowt! Cheers Mel!

A standard, no frills front bumper

Step two: roughly cut around the area required before some more delicate trimming.

Step three: closer trimming around the fins and legs prior to trial fitting. For this I used a Dremel with a drill bit, making regular perforations along the desired cut line and then joining the dots to make the final cut. Cleaning up the rough edges can then be done, surprisingly, by warming the plastic up and cutting with a good pair of scissors!

I'll hopefully finish this job between Christmas and New Year. You never know, I might even get some carpeting done too!

Wanted: Standard front bumper

Have you got one lying around from a recent conversion?

I only need the lower middle fins as shown below:

Leave a comment below or email rpcreative@hotmail.com

UPDATE: One bumper collected from a fellow Caddy2k forum member. I've another one waiting in the wings too (in case I make a mess of this first one!).

Exterior: to-do list

Having had a fairly miserable day wrestling with the two large ply panels from the back of the van (unscrew, lift them out, trim a bit, screw them in, out again, trim a bit, repeat, repeat, repeat...) I thought I'd cheer myself with a spot of Photoshop-modding.

With the Bentley wheels now sold I'm currently in discussions with a chap from the Caddy2k forum who has several sets of VW Helios wheels being refurbished. One of these sets now has my name on them!

The Helios was an optional-extra on Volkswagen's luxury Phaeton range. So as you can imagine, they're pretty hard to come by. You could walk into your local dealership and order a set. Better still you could go to your local TPS and price a set up. This would currently cost you over two and a half grand!!!

Anyway, back to the Photoshopping:

Click for bigger version

The 19's immediately look more at home (and less like an exaggerated Hot-Wheels toy) than the 20" Bentleys. Being from the Volkswagen family sits well with me; I'm a big fan of the OEM+ look or in other words 'what VW would have done if they could dip into the parts bin regardless of cost'.

Black headlights from a Touran R-line help set the Caddy off from being just another van - these are a straight swap too; no messing, trimming or fudging required.

Wind deflectors - just because I like them - will probably look for a slimline set from Heko.

Sliding door rail cover - I'll be looking to get one of the excellent kits from Reflex Auto Design - as these come painted I might also treat myself to the Sportline rear spoiler at the same time.

Finally, I'll be looking into reinstating the fins that have been cut away from the lower part of the front bumper. Initially I'll be looking to source a secondhand bumper off eBay and chopping it up. If that doesn't work I might push the boat out and fit a Touran front end.

Oh, and there's another part in the post - a little something for under the bonnet - will keep you posted when fitted...